Shanghai Runwell Machinery Equipment Co.,Ltd
Shanghai Runwell Machinery Equipment Co., LTD.
Add to Cart
Spring cone crusher is suitable to crush kinds of ores and rocks with medium hardness and above. It has features of reliable structure,high efficiency,high capacity,low operating cost,easy adjustment ,economical to use and so on. Spring system plays the role of overload protection, which will enable the exotic materials or steel piece to pass through the crushing chamber without any damage to the machine. It adopts grease seal to isolate dust and lubricants, therefore ensure its reliable operation. According to customer demand, respectively, using standard type, medium type and short head type for coarse crushing, medium crushing and fine crushing operation.
Spring cone crusher working principle :During operation, the motor of goodpy series spring cone crusher price drives the eccentric shaft shell to turn around through a horizontal axle and a pair of bevel gear. The axle of crushing cone swings with the force of eccentric shaft shell so that the surface of the crushing wall is close to the roll mortar wall from time to time. In this way, the ores and rocks will be pressed and crooked and crushed. To ensure the precision of thrust bearing installation in spring cone crusher, installation must be the following steps: first, the installation of the thrust bearing should be same to steps of scratching; jaw plate placed in a case back should be smooth,if case back has the burr and the remaining sand,please clean up.Then pour lubricating oil to just the top of jaw plate. then install the middle circle plate and circle plate. Finally, install the air eccentric shaft, spherical tile racks, and spindle. When installing air eccentric shaft,the big gear weight should be placed in the top of small gear,so that the outer end of bevel gear is alignment. After spherical wham installed, the gap between spherical bearing seat and the main machine is as big as possible.
spring cone crusher technology specfications:
| Type | Dia. of Cone (mm) | Adjusting Range of Discharge Opening (mm) | Max Feed Size (mm) | Capacity (t/h) | Motor Power (kw) | Weight (t) | Overall Dimension (mm) |
| PYB-600 | 600 | 12-25 | 65 | 15-25 | 30 | 5.5 | 1740×1225×1940 |
| PYD-600 | 3-13 | 36 | 5-23 | 30 | 5.5 | 1740×1225×1940 | |
| PYB-900 | 900 | 15-50 | 115 | 50-90 | 55 | 10.18 | 1990×1640×2380 |
| PYZ-900 | 5-20 | 60 | 20-65 | 55 | 10.19 | 1990×1640×2380 | |
| PYD-900 | 3-13 | 40 | 15-50 | 55 | 10.27 | 1990×1640×2380 | |
| PYB-1200 | 1200 | 20-50 | 145 | 110-200 | 110 | 24.7 | 2805×2300×2980 |
| PYZ-1200 | 8-26 | 100 | 50-150 | 110 | 25 | 2805×2300×2980 | |
| PYD-1200 | 3-15 | 50 | 18-105 | 110 | 25.6 | 2805×2300×2980 | |
| PYB-1750 | 1750 | 25-60 | 215 | 280-480 | 155-160 | 50.6 | 3610×2950×4185 |
| PYZ-1750 | 10-30 | 185 | 115-320 | 155-160 | 51 | 3610×2950×4185 | |
| PYD-1750 | 5-15 | 85 | 75-230 | 155-160 | 50.5 | 3610×2950×4185 | |
| PYB-2200 | 2200 | 30-60 | 300 | 590-1000 | 260-280 | 84 | 4790×3430×5080 |
| PYZ-2200 | 10-30 | 235 | 200-580 | 260-280 | 85 | 4790×3430×5080 | |
| PYD-2200 | 5-16 | 110 | 120-370 | 260-280 | 85 | 4790×3430×4852 |
Q1: Where your products have been exported before?
A1: Our products have been sold to South Asia, Africa, South America, middle East and so on.
Q2: How will you help the customer to install the equipment?
A2: Our senior engineer will guide the installation and commissioning at your place.
Q3: How about the wear parts supply?
A3: We offer wear parts to our customer with our most favorable price. If there are problems youcould not handle, we will send our technicians to your place.
Q4: What about the payment method?
A4:T/T, L/C,D/P is available
Q5: What about after-sale service?
A5:12 months warranty for all kinds of products.